View LT6660_298941.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FEATURES

LT6660 Tiny Micropower Precision Series References in 2mm x 2mm DFN DESCRIPTIO
The LT(R)6660 is a family of micropower series references that combine high accuracy and low drift with low power dissipation and extremely small package size. These series references use curvature compensation to obtain low temperature coefficient, and laser trimmed precision thin-film resistors to achieve high output accuracy. The LT6660 will supply up to 20mA with excellent line regulation characteristics, making it ideal for precision regulator applications. The LT6660 family of series references provide supply current and power dissipation advantages over shunt references that must idle the entire load current to operate. Additionally, the LT6660 does not require an output compensation capacitor. This feature is important in applications where PC board space is a premium, fast settling is demanded, or total capacitance must be kept to a minimum, as in intrinsic safety applications. Reverse-battery protection keeps these references from conducting reverse current.
, LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners.
3-Lead 2mm x 2mm x 0.75mm DFN Package No Output Capacitor Required Low Drift: 20ppm/C Max High Accuracy: 0.2% Max Low Supply Current 20mA Output Current Guaranteed Reverse-Battery Protection Low IR Reflow Induced Stress: 0.02% Typ Voltage Options: 2.5V, 3V, 3.3V, 5V and 10V Space-Saving Alternative to the LT1460
APPLICATIO S

Handheld Instruments Precision Regulators A/D and D/A Converters Power Supplies Hard Disk Drives Sensor Modules
TYPICAL APPLICATIO
LT6660H VOUT Shift Due to IR Reflow
32 28
Basic Connection
DISTRIBUTION (%) LT6660 VOUT + 0.9V VIN 20V C1 0.1F IN GND
6660 TA01
24 20 16 12 8 4 0 -0.09 -0.05 -0.01 0.01 0.05 CHANGE IN VOUT (%) 0.09
6660 TA01b
OUT
VOUT
U
U
U
6660f
1
LT6660 ABSOLUTE
(Note 1)
AXI U RATI GS
Operating Temperature Range (Note 2) ............................................... -40C to 85C Storage Temperature Range (Note 3)..... -65C to 150C Lead Temperature (Soldering, 10 sec) .................. 300C
Input Voltage.............................................................30V Reverse Voltage ......................................................-15V Output Short-Circuit Duration, TA = 25C ................5 sec Specified Temperature Range ...................... 0C to 70C
PACKAGE/ORDER I FOR ATIO
TOP VIEW
4
1 OUT
2 GND
3 IN
DC PACKAGE 3-LEAD (2mm x 2mm) PLASTIC DFN TJMAX = 125C, JA = 102C/W EXPOSED PAD IS GND, MUST BE SOLDERED TO PCB
Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
AVAILABLE OPTIONS
OUTPUT VOLTAGE (V) 2.5 2.5 2.5 3 3 3 3.3 3.3 3.3 SPECIFIED TEMPERATURE RANGE 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C ACCURACY (%) 0.2 0.4 0.5 0.2 0.4 0.5 0.2 0.4 0.5 TEMPERATURE COEFFICIENT (ppm/C) 20 20 50 20 20 50 20 20 50 PART ORDER NUMBER LT6660HCDC-2.5 LT6660JCDC-2.5 LT6660KCDC-2.5 LT6660HCDC-3 LT6660JCDC-3 LT6660KCDC-3 LT6660HCDC-3.3 LT6660JCDC-3.3 LT6660KCDC-3.3
2
U
U
W
WW U
W
ORDER PART NUMBER LT6660HCDC-2.5 LT6660JCDC-2.5 LT6660KCDC-2.5 LT6660HCDC-3 LT6660JCDC-3 LT6660KCDC-3 LT6660HCDC-3.3 LT6660JCDC-3.3 LT6660KCDC-3.3 LT6660HCDC-5 LT6660JCDC-5 LT6660KCDC-5 LT6660HCDC-10 LT6660JCDC-10 LT6660KCDC-10
DFN PART MARKING* LBXN LBXN LBXN LBYV LBYV LBYV LBYW LBYW LBYW LBYT LBYT LBYT LBYX LBYX LBYX
6660f
LT6660 AVAILABLE OPTIONS
OUTPUT VOLTAGE (V) 5 5 5 10 10 10 SPECIFIED TEMPERATURE RANGE 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C ACCURACY (%) 0.2 0.4 0.5 0.2 0.4 0.5 TEMPERATURE COEFFICIENT (ppm/C) 20 20 50 20 20 50 PART ORDER NUMBER LT6660HCDC-5 LT6660JCDC-5 LT6660KCDC-5 LT6660HCDC-10 LT6660JCDC-10 LT6660KCDC-10
ELECTRICAL CHARACTERISTICS
PARAMETER Output Voltage Tolerance
The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = VOUT + 2.5V, IOUT = 0 unless otherwise specified.
CONDITIONS LT6660HCDC LT6660JCDC LT6660KCDC LT6660HCDC LT6660JCDC LT6660KCDC VOUT + 0.9V VIN VOUT + 2.5V VOUT + 2.5V VIN 20V MIN -0.2 -0.4 -0.5 50 1000 50 20 2.5 40 0.5 4 4 100 50 250 115 LT6660-3 LT6660-3.3 LT6660-5 LT6660-10 215 160 145 145 145 175 180 220 180 220 200 240 270 350 TYP MAX 0.2 0.4 0.5 20 20 50 800 1000 100 130 3000 4000 200 300 70 100 10 0.9 1.3 1.4 10 UNITS % % % ppm/C ppm/C ppm/C ppm/V ppm/V ppm/V ppm/V ppm/mA ppm/mA ppm/mA ppm/mA ppm/mA ppm/mA ppm/mW V V V mA A ppm (P-P) ppm (RMS) ppm/kHr ppm ppm A A A A A A A A A A
6660f
Output Voltage Temperature Coefficient (Note 4)
10 10 25 150
Line Regulation
Load Regulation Sourcing (Note 5)
IOUT = 100A IOUT = 10mA IOUT = 20mA
Thermal Regulation (Note 6) Dropout Voltage (Note 7)
P = 200mW VIN - VOUT, VOUT 0.2%, IOUT = 0 VIN - VOUT, VOUT 0.2%, IOUT = 10mA
Output Current Reverse Leakage Output Voltage Noise (Note 8) Long-Term Stability of Output Voltage (Note 9) Hysteresis (Note 10) Supply Current
Short VOUT to GND VIN = -15V 0.1Hz f 10Hz 10Hz f 1kHz T = 0C to 70C T = -40C to 85C LT6660-2.5

3
LT6660 ELECTRICAL CHARACTERISTICS
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT6660 is guaranteed functional over the operating temperature range of -40C to 85C. Note 3: If the parts are stored outside of the specified temperature range, the output may shift due to hysteresis. Note 4: Temperature coefficient is measured by dividing the change in output voltage by the specified temperature range. Incremental slope is also measured at 25C. Note 5: Load regulation is measured on a pulse basis from no load to the specified load current. Output changes due to die temperature change must be taken into account separately. Note 6: Thermal regulation is caused by die temperature gradients created by load current or input voltage changes. This effect must be added to normal line or load regulation. This parameter is not 100% tested. Note 7: Excludes load regulation errors. Note 8: Peak-to-peak noise is measured with a single pole highpass filter at 0.1Hz and 2-pole lowpass filter at 10Hz. The unit is enclosed in a still-air environment to eliminate thermocouple effects on the leads. The test time is 10 sec. RMS noise is measured with a single pole highpass filter at 10Hz and a 2-pole lowpass filter at 1kHz. The resulting output is full wave rectified and then integrated for a fixed period, making the final reading an average as opposed to RMS. A correction factor of 1.1 is used to convert from average to RMS and a second correction of 0.88 is used to correct for the nonideal bandpass of the filters. Note 9: Long-term stability typically has a logarithmic characteristic and therefore, changes after 1000 hours tend to be much smaller than before that time. Total drift in the second thousand hours is normally less than one third that of the first thousand hours with a continuing trend toward reduced drift with time. Long-term stability will also be affected by differential stresses between the IC and the board material created during board assembly. Note 10: Hysteresis in output voltage is created by package stress that differs depending on whether the IC was previously at a higher or lower temperature. Output voltage is always measured at 25C, but the IC is cycled to 70C or 0C before successive measurements. Hysteresis is roughly proportional to the square of the temperature change. For instruments that are stored at well-controlled temperatures (within 20 or 30 degrees of operational temperature) hysteresis is not a problem.
TYPICAL PERFOR A CE CHARACTERISTICS
2.5V Minimum Input-Output Voltage Differential
100 OUTPUT VOLTAGE CHANGE (mV) 0 - 0.5 - 1.0 - 55C - 1.5 - 2.0 25C - 2.5 125C - 3.0 - 3.5 - 4.0 0.1 1 10 OUTPUT CURRENT (mA)
Characteristic curves are similar for all voltage options of the LT6660. Curves from the LT6660-2.5 and the LT6660-10 represent the extremes of the voltage options. Characteristic curves for other output voltages fall between these curves, and can be estimated based on their voltage output.
OUTPUT VOLTAGE CHANGE (mV)
OUTPUT CURRENT (mA)
10
125C
25C 1 - 55C
0.1 0 0.5 1.0 1.5 2.0 INPUT-OUTPUT VOLTAGE (V) 2.5
6660 G01
4
UW
2.5V Load Regulation, Sourcing
120 100 80 60
2.5V Load Regulation, Sinking
25C 40 20 0
125C
- 55C
100
6660 G02
0
1
2 3 4 OUTPUT CURRENT (mA)
5
6660 G03
6660f
LT6660 TYPICAL PERFOR A CE CHARACTERISTICS
2.5V Output Voltage Temperature Drift
2.503 2.502 SUPPLY CURRENT (A) OUTPUT VOLTAGE (V) 2.501 2.500 2.499 2.498 2.497 -50 -25 THREE TYPICAL PARTS 250 25C OUTPUT VOLTAGE (V) 125C 150 - 55C
Characteristic curves are similar for all voltage options of the LT6660. Curves from the LT6660-2.5 and the LT6660-10 represent the extremes of the voltage options. Characteristic curves for other output voltages fall between these curves, and can be estimated based on their voltage output. 2.5V Supply Current vs Input Voltage
2.502 2.501 25C 2.500 2.499 2.498 125C 2.497 2.496 2.495 50 25 75 0 TEMPERATURE (C) 100 125 0 2.494 0 5 10 INPUT VOLTAGE (V)
6660 G04 6660 G05
2.5V Power Supply Rejection Ratio vs Frequency
80 POWER SUPPLY REJECTION RATIO (dB) 70 OUTPUT IMPEDANCE () 60 50 40 30 20 10 0 0.1 1 10 100 FREQUENCY (kHz) 1000
6660 G07
100
CL = 0.1F
LOAD CURRENT (mA)
2.5V Output Voltage Noise Spectrum
1000
NOISE VOLTAGE (nV/Hz)
100 10 100 1k 10k FREQUENCY (Hz) 100k
6660 G10
OUTPUT NOISE (20V/DIV)
UW
2.5V Line Regulation
200
- 55C
100
50
15
20
0
2
4
6 8 10 12 14 16 18 20 INPUT VOLTAGE (V)
6660 G06
2.5V Output Impedance vs Frequency
1000 CL = 0F 20
2.5V Transient Response
10
10 CL = 1F 1
1
0.1 200s/DIV CLOAD = 0F
6660 G09
0.1 0.01
0.1
1 10 FREQUENCY (kHz)
100
1000
6660 G08
2.5V Output Noise 0.1Hz to 10Hz
TIME (2 SEC/DIV)
6660 G11
6660f
5
LT6660 TYPICAL PERFOR A CE CHARACTERISTICS
10V Minimum Input-Output Voltage Differential
100 OUTPUT VOLTAGE CHANGE (mV) 35 30 OUTPUT VOLTAGE CHANGE (mV) OUTPUT CURRENT (mA) 25 20 15 10 5 0 -5 0.1 0 0.5 1.0 1.5 2.0 INPUT-OUTPUT VOLTAGE (V) 2.5
6660 G12
Characteristic curves are similar for all voltage options of the LT6660. Curves from the LT6660-2.5 and the LT6660-10 represent the extremes of the voltage options. Characteristic curves for other output voltages fall between these curves, and can be estimated based on their voltage output.
10
125C
25C 1 - 55C
10V Output Voltage Temperature Drift
10.006 10.004 10.002 SUPPLY CURRENT (A) OUTPUT VOLTAGE (V) 10.000 9.998 9.996 9.994 9.992 9.990 9.988 9.986 9.984 9.982 - 50 - 25 0 50 25 0 75 TEMPERATURE (C) 100 125 THREE TYPICAL PARTS 350 300
250 125C 200 150 100 50 - 55C
OUTPUT VOLTAGE (V)
6
UW
10V Load Regulation, Sourcing
250
10V Load Regulation, Sinking
200 125C 150 25C 100 -55C 50
- 55C 125C 25C 100
6660 G13
-10 0.1
1 10 OUTPUT CURRENT (mA)
0
0
1
3 4 2 OUTPUT CURRENT (mA)
5
6660 G14
10V Supply Current vs Input Voltage
10.010 10.005 10.000 9.995 9.990 9.985 9.980 0 2 4 6 8 10 12 14 16 18 20 INPUT VOLTAGE (V)
6660 G16
10V Line Regulation
25C
25C - 55C 125C
6
8
14 12 16 10 INPUT VOLTAGE (V)
18
20
6660 G15
6660 G17
6660f
LT6660 TYPICAL PERFOR A CE CHARACTERISTICS
10V Power Supply Rejection Ratio vs Frequency
100 POWER SUPPLY REJECTION RATIO (dB) 90 80 OUTPUT IMPEDANCE () 70 60 50 40 30 20 10 0 0.1 1 10 100 FREQUENCY (kHz) 1000
6660 G18
Characteristic curves are similar for all voltage options of the LT6660. Curves from the LT6660-2.5 and the LT6660-10 represent the extremes of the voltage options. Characteristic curves for other output voltages fall between these curves, and can be estimated based on their voltage output. 10V Output Impedance vs Frequency
1000 20 100 CL = 0.1F LOAD CURRENT (mA) CL = 0F
10V Output Voltage Noise Spectrum
10
1
0.1 0.01
0.1
1 10 FREQUENCY (kHz)
100
6660 G21
OUTPUT NOISE (20V/DIV)
NOISE VOLTAGE (V/Hz)
UW
10V Transient Response
10
10
1
CL = 1F 1
0.1 200s/DIV CLOAD = 0F
6660 G20
0.1 0.01
0.1
1 10 FREQUENCY (kHz)
100
1000
6660 G19
10V Output Noise 0.1Hz to 10Hz
TIME (2 SEC/DIV)
6660 G22
6660f
7
LT6660 APPLICATIO S I FOR ATIO
Longer Battery Life Series references have a large advantage over older shunt style references. Shunt references require a resistor from the power supply to operate. This resistor must be chosen to supply the maximum current that can ever be demanded by the circuit being regulated. When the circuit being controlled is not operating at this maximum current, the shunt reference must always sink this current, resulting in high dissipation and short battery life. The LT6660 series references do not require a current setting resistor and can operate with any supply voltage from VOUT + 0.9V to 20V. When the circuitry being regulated does not demand current, the LT6660s reduce their dissipation and battery life is extended. If the references are not delivering load current, they dissipate only several mW, yet the same connection can deliver 20mA of load current when demanded. Capacitive Loads The LT6660 family of references are designed to be stable with a large range of capacitive loads. With no capacitive load, these references are ideal for fast settling or applications where PC board space is a premium. The test circuit shown in Figure 1 is used to measure the response time and stability of various load currents and load capacitors. This circuit is set for the 2.5V option. For other voltage options, the input voltage must be scaled up and the output voltage generator offset voltage must be adjusted. The 1V step from 2.5V to 1.5V produces a current step of 10mA or 1mA for RL = 100 or RL = 1k. Figure 2 shows the response of the reference to these 1mA and 10mA load steps with no load capacitance, and Figure 3 shows a 1mA and 10mA load step with a 0.1F output capacitor. Figure 4 shows the response to a 1mA load step with CL = 1F and 4.7F.
VIN = 2.5V CIN 0.1F LT6660-2.5 VOUT CL RL VGEN 2.5V 1.5V
6660 F01
Figure 1. Response Time Test Circuit
8
U
VGEN 2.5V 1.5V VOUT 1mA VOUT 10mA 1s/DIV
6660 F02
W
U
U
Figure 2. CL = 0F
VGEN
2.5V 1.5V
VOUT
1mA
VOUT
10mA
100s/DIV
6660 F03
Figure 3. CL = 0.1F
VGEN
2.5V 1.5V
VOUT
1F
VOUT
4.7F
100s/DIV
6660 F04
Figure 4. IOUT = 1mA
6660f
LT6660 APPLICATIO S I FOR ATIO
Table 1 gives the maximum output capacitance for various load currents and output voltages to avoid instability. Load capacitors with low ESR (effective series resistance) cause more ringing than capacitors with higher ESR such as polarized aluminum or tantalum capacitors.
Table 1. Maximum Output Capacitance
VOLTAGE OPTION 2.5V 3V 3.3V 5V 10V IOUT = 100A >10F >10F >10F >10F >10F IOUT = 1mA >10F >10F >10F >10F 1F IOUT = 10mA 2F 2F 1F 1F 0.15F IOUT = 20mA 0.68F 0.68F 0.68F 0.68F 0.1F
Long-Term Drift Long-term drift cannot be extrapolated from accelerated high temperature testing. This erroneous technique gives drift numbers that are wildly optimistic. The only way long-term drift can be determined is to measure it over the time interval of interest. The LT6660 long-term drift data was taken on over 100 parts that were soldered into PC boards similar to a "real world" application. The boards were then placed into a constant temperature oven with TA = 30C, their outputs were scanned regularly and measured with an 8.5 digit DVM. Figure 5 shows typical long-term drift of the LT6660s.
150 100 50 ppm 0 - 50 -100 -150 0 100 200 300 400 500 600 700 800 900 1000 HOURS
6660 F05
NUMBER OF UNITS
NUMBER OF UNITS
Figure 5. Typical Long-Term Drift
U
Hysteresis Hysteresis data shown in Figure 6 and Figure 7 represents the worst-case data taken on parts from 0C to 70C and from -40C to 85C. The output is capable of dissipating relatively high power, i.e., for the LT6660-2.5, PD = 17.5V * 20mA = 350mW. The thermal resistance of the DFN package is 102C/W and this dissipation causes a 36C internal rise. This elevated temperature may cause the output to shift due to thermal hysteresis. For highest performance in precision applications, do not let the LT6660's junction temperature exceed 85C. Input Capacitance It is recommended that a 0.1F or larger capacitor be added to the input pin of the LT6660. This can help with stability when large load currents are demanded.
18 16 14 12 10 70C TO 25C 8 6 4 2 0 -240 -200 -160 -120 - 80 -40 0 40 HYSTERESIS (ppm) 80 120 160 200 240
6660 F06
W
U
U
WORST-CASE HYSTERESIS ON 40 UNITS
0C TO 25C
Figure 6. 0C to 70C Hysteresis
9 8 7 85C TO 25C 6 5 4 3 2 1 0 -600 -500 -400 -300 -200 -100 0 100 200 300 400 500 600 HYSTERESIS (ppm)
6660 F07
WORST-CASE HYSTERESIS ON 34 UNITS -40C TO 25C
Figure 7. - 40C to 85C Hysteresis
6660f
9
LT6660 APPLICATIO S I FOR ATIO
Output Accuracy Like all references, either series or shunt, the error budget of the LT6660s is made up of primarily three components: initial accuracy, temperature coefficient and load regulation. Line regulation is neglected because it typically contributes only 150ppm/V. The LT6660s typically shift 0.02% when soldered into a PCB, so this is also neglected. The output errors are calculated as follows for a 100A load and 0C to 70C temperature range: LT6660HCDC Initial Accuracy = 0.2% For IOUT = 100A VOUT = (4000ppm/mA)(0.1mA) = 0.04% For Temperature 0C to 70C the maximum T = 70C VOUT = (20ppm/C)(70C) = 0.14%
10
U
Total worst-case output error is: 0.2% + 0.04% + 0.14% = 0.380% Table 2 gives the worst-case accuracy for LT6660HC, LT6660JC and LT6660KC from 0C to 70C, and shows that if the LT6660HC is used as a reference instead of a regulator, it is capable of 8 bits of absolute accuracy over temperature without a system calibration.
Table 2. Worst-Case Output Accuracy over Temperature
IOUT 0A 100A 10mA 20mA LT6660HCDC 0.340% 0.380% 0.640% 0.540% LT6660JCDC 0.540% 0.580% 0.840% 0.740% LT6660KCDC 0.850% 0.890% 1.15% 1.05%
6660f
W
U
U
LT6660 PACKAGE DESCRIPTIO U
DC Package 3-Lead Plastic DFN (2mm x 2mm) (Reference LTC DWG # 05-08-1717 Rev O)
1.35 0.05 (2 SIDES) PACKAGE OUTLINE 0.25 0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 1.35 0.05 (2 SIDES) R = 0.05 TYP 2.00 0.10 (4 SIDES) 1.00 0.05 (2 SIDES) PIN 1 NOTCH R = 0.20 OR 0.25 x 45 CHAMFER 3 1 R = 0.115 TYP 0.25 0.05 0.50 BSC
(DC3) DFN 1205 REV O
1.00 0.05 1.30 0.05 (2 SIDES) 2.00 0.05
PIN 1 BAR TOP MARK (SEE NOTE 6)
0.40 0.05 0.200 REF 0.75 0.05 0.70 0.05
BOTTOM VIEW--EXPOSED PAD
0.00 - 0.05 NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (W-TBD) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE
6660f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
11
LT6660 TYPICAL APPLICATIO U
Handling Higher Load Currents
V+ 40mA
+
47F
3 IN LT6660 OUT GND 2 RL TYPICAL LOAD CURRENT = 50mA 1 10mA VOUT R1*
*SELECT R1 TO DELIVER 80% OF TYPICAL LOAD CURRENT. LT1460 WILL THEN SOURCE AS NECESSARY TO MAINTAIN PROPER OUTPUT. DO NOT REMOVE LOAD AS OUTPUT WILL BE DRIVEN UNREGULATED HIGH. LINE REGULATION IS DEGRADED IN THIS APPLICATION
R1 =
V + - VOUT 40mA
6660 TA02
Boosted Output Current with No Current Limit
V + (VOUT + 1.8V) R1 220 2N2905 3 IN LT6660 OUT GND 2 1 VOUT 100mA 2F SOLID TANT
Boosted Output Current with Current Limit
V+ VOUT + 2.8V D1* LED R1 220
+
47F
+
8.2 2N2905 47F
3 IN LT6660 OUT GND 2 * GLOWS IN CURRENT LIMIT, DO NOT OMIT 1 VOUT 100mA 2F SOLID TANT
6660 TA04
+
+
6660 TA03
RELATED PARTS
PART NUMBER LT1019 LT1027 LT1236 LT1460 LT1461 LT1634 LT1790 LTC 1798
(R)
DESCRIPTION Precision Bandgap Reference Precision 5V Reference Precision Low Noise Reference Micropower Series References Micropower Precision Low Dropout Micropower Precision Shunt Reference 1.25V, 2.5V Output Micropower Precision Series References Micropower Low Dropout Reference, Fixed or Adjustable
COMMENTS 0.05% Max, 5ppm/C Max 0.02%, 2ppm/C Max 0.05% Max, 5ppm/C Max, SO Package 0.075% Max, 10ppm/C Max, 20mA Output Current 0.04% Max, 3ppm/C Max, 50mA Output Current 0.05%, 25ppm/C Max 0.05% Max, 10ppm/C Max, 60A Supply, SOT23 Package 0.15% Max, 40ppm/C, 6.5A Max Supply Current
6660f
12 Linear Technology Corporation
(408) 432-1900 FAX: (408) 434-0507
LT 0106 * PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
www.linear.com
(c) LINEAR TECHNOLOGY CORPORATION 2006

▲Up To Search▲

Price & Availability of LT6660

	To Download LT6660 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .